... continued
1. Start construction of waste oil stove by chalking off and cutting out access door on the side of the stripped water heater tank. | |||||||||||||||||
2. All cuts -- whether torched or sawed -- should be filed smooth. | |||||||||||||||||
3. The stack holes on tank's top are next chalked (left) and ... | |||||||||||||||||
4. ... cut. | |||||||||||||||||
5. Tank is then turned upside down so the support flange for stove's burner assembly can be mounted and ... | |||||||||||||||||
6. ... the furnace's legs bolted to the container's bottom.
|
7. Here's all the hardware for the burner assembly which, like everything else ... | |||||||||||||||||||
8. ... just bolts together.
|
|||||||||||||||||||
9. The chimney stack is pushed at least six inches down into its hole and secured with bolts and angle iron tabs.
|
|||||||||||||||||||
10. A funnel is made from some of the junked water heater's sheet metal skin and ...
|
|||||||||||||||||||
12. ... pushed through access door and wedged up through its hole in the top of the converted tank. | |||||||||||||||||||
11. ... fitted to the lower end of intake stack, which is then ... |
15. Although not absolutely necessary, a spacer ring can be bent up from hanger strap and ... | |||||||||||||||||||
14. A 4-inch, 90-degree elbow is fitted to a hole in the side of a 12-inch-long section of 8-inch stovepipe and this "pre-heater" is positioned over the feeder tubing. | |||||||||||||||||||
13. The copper tubing fuel feeder is then wrapped around chimney stack and its end positioned over the intake stack. | |||||||||||||||||||
18. A collar -- cut from the old water heater's sheet metal skin -- can be added to cover the clamp. | |||||||||||||||||||
17. "Pre-heater/intake stack" assembly is locked into position with a simple clamp. | |||||||||||||||||||
16. ... used to center pre-heater stovepipe on chimney stack. | |||||||||||||||||||
20. Salvaged tank's heating element holes are sealed with 1/8-inch steel plates.
|
|||||||||||||||||||
19. View of inside of partially completed furnace door. | |||||||||||||||||||
22. A short angle iron "handle", a peephole covered by a movable metal flap, and a window latch fastener complete the furnace's door.
|
||||||||||||
21. The completed furnace's burner assembly is filled with crushed asbestos or an asbestos brick [use perlite]. As an added fire precaution, the bottom of the stove is then filled with sand. | ||||||||||||
23. MOTHER's waste oil burner gets a light from Richard Freudenberger. | ||||||||||||
24. The blaze is just getting started ... and already Richard can feel the heat. |
To
MOTHER's Waste Oil Heater -- original version
Instructions in a nutshell
Feedback
Journey to Forever's Waste Oil HeaterModifications:
Roger Sanders' Waste Oil Heater
Bruce Woodford's forced-air waste oil heater
Journey to Forever's forced-air biofuel heater
To Mother Earth Alcohol Fuel, Table of Contents
Biofuels
En español -- Biocombustibles, biodiesel
Biofuels Library
Biofuels supplies and suppliers
Biodiesel
Make your own biodiesel
Mike Pelly's recipe
Two-stage biodiesel process
FOOLPROOF biodiesel process
Biodiesel processors
Biodiesel in Hong Kong
Nitrogen Oxide emissions
Glycerine
Biodiesel resources on the Web
Do diesels have a future?
Vegetable oil yields and characteristics
Washing
Biodiesel and your vehicle
Food or fuel?
Straight vegetable oil as diesel fuel
Ethanol
Ethanol resources on the Web
Is ethanol energy-efficient?
Community development | Rural development
City farms | Organic gardening | Composting | Small farms | Biofuel | Solar box cookers
Trees, soil and water | Seeds of the world | Appropriate technology | Project vehicles
Home | What people are saying about us | About Handmade Projects
Projects | Internet | Schools projects | Sitemap | Site Search | Donations | Contact us